oak:tutorials:relay
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
oak:tutorials:relay [2016/02/22 09:02] wminarik [Product Description:] |
oak:tutorials:relay [2016/02/22 09:06] wminarik [Assembly:] |
||
|---|---|---|---|
| Line 18: | Line 18: | ||
| ^ Part ^ Quantity ^Identification^ | ^ Part ^ Quantity ^Identification^ | ||
| | Oak Relay Shield PCB|1| | | | Oak Relay Shield PCB|1| | | ||
| - | | Relay with 3VDC coil|1| | + | | Relay with 3VDC coil|1| JQC-3F (T73) | |
| | 1K ohm 1/4 W resistor 5%|1| Brown - Black - Red| | | 1K ohm 1/4 W resistor 5%|1| Brown - Black - Red| | ||
| | 1N001 diode|1| | | | 1N001 diode|1| | | ||
| - | | 2N3904 transistor |1| NPN TO-92 package| | + | | 2N3904 NPN transistor |1| TO-92 package| |
| | 3-pin screw terminal |1| | | | 3-pin screw terminal |1| | | ||
| | 1x40 pin male 0.1" pitch header| 9 pins worth| | | | 1x40 pin male 0.1" pitch header| 9 pins worth| | | ||
| Line 44: | Line 44: | ||
| [[https://s3.amazonaws.com/digispark/images/m/3v3-relay-shield-1.jpg|{{https://s3.amazonaws.com/digispark/images/t/3v3-relay-shield-1.jpg}}]] | [[https://s3.amazonaws.com/digispark/images/m/3v3-relay-shield-1.jpg|{{https://s3.amazonaws.com/digispark/images/t/3v3-relay-shield-1.jpg}}]] | ||
| - | Solder the leads of the resistor. Place the diode in the orientation indicated (silver band over band silkscreen) and solder. Clip off the excess as pictured (also shown are solder pads on the reverse for changing the controlling digital pin). | + | Place and solder the leads of the resistor. Place the diode in the orientation indicated (silver band over band silkscreen) and solder. Clip off the excess as pictured (also shown are solder pads on the reverse for changing the controlling digital pin). |
| [[https://s3.amazonaws.com/digispark/images/m/3v3-relay-shield-2.jpg|{{https://s3.amazonaws.com/digispark/images/t/3v3-relay-shield-2.jpg}}]] | [[https://s3.amazonaws.com/digispark/images/m/3v3-relay-shield-2.jpg|{{https://s3.amazonaws.com/digispark/images/t/3v3-relay-shield-2.jpg}}]] | ||
| [[https://s3.amazonaws.com/digispark/images/m/3v3-relay-shield-3.jpg|{{https://s3.amazonaws.com/digispark/images/t/3v3-relay-shield-3.jpg}}]] | [[https://s3.amazonaws.com/digispark/images/m/3v3-relay-shield-3.jpg|{{https://s3.amazonaws.com/digispark/images/t/3v3-relay-shield-3.jpg}}]] | ||
| - | Then solder and clip the leads of the NPN transistor. Make sure that it doesn't overhang the spot reserved for the relay. | + | Insert the NPN transistor, matching the shape with the printing on the board and solder and clip the leads. Make sure that it doesn't overhang the spot reserved for the relay. |
| [[https://s3.amazonaws.com/digispark/images/m/3v3-relay-shield-4.jpg|{{https://s3.amazonaws.com/digispark/images/t/3v3-relay-shield-4.jpg}}]] | [[https://s3.amazonaws.com/digispark/images/m/3v3-relay-shield-4.jpg|{{https://s3.amazonaws.com/digispark/images/t/3v3-relay-shield-4.jpg}}]] | ||
oak/tutorials/relay.txt · Last modified: 2016/03/10 22:47 by digistump
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
