Digistump Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
//**THIS TUTORIAL HAS NOT YET BEEN REVIEWED, PLEASE DO NOT USE UNTIL IT HAS**//

======Prototype Shield Kit Tutorial======

=====Product Description:=====
[[https://s3.amazonaws.com/digispark/images/m/oak-prototype-shield-1.jpg|{{https://s3.amazonaws.com/digispark/images/t/oak-prototype-shield-1.jpg}}]]
[[https://s3.amazonaws.com/digispark/images/m/oak-prototype-shield-2.jpg|{{https://s3.amazonaws.com/digispark/images/t/oak-prototype-shield-2.jpg}}]]
[[https://s3.amazonaws.com/digispark/images/m/oak-prototype-shield-4.jpg|{{https://s3.amazonaws.com/digispark/images/t/oak-prototype-shield-4.jpg}}]]


The Prototype Shield Kit breaks out the connections on the Digistump Oak development board and provides a small through hole soldering area for building custom circuits.

This is an unassembled kit and requires basic soldering. This is designed for use with the Digistump Oak development board, which is not included.

=====Parts:=====

^ Part       ^ Quantity          ^Identification^
| Oak Prototype Shield PCB|1| |
|  1x40pin male 0.1" pitch header| 21 pins worth| |

**Soldering:** If you are new to soldering we recommend the following tutorials:
Soldering Basics (http://www.sparkfun.com/tutorials/106) and Soldering Crash Course from the folks at Sparkfun (http://www.sparkfun.com/tutorials/354).
How to solder from the Curious Inventor: http://store.curiousinventor.com/guides/How_to_Solder

Adafruit has this excellent guide that starts with the tools needed and then shows detailed pictures, including some of the common problems that beginners experience (http://learn.adafruit.com/adafruit-guide-excellent-soldering)

**We assume for these assembly instructions that you know the basics of thru-hole soldering. If you don't check out the links above, these boards are very easy to solder - we promise!**


=====Assembly:=====

[[https://s3.amazonaws.com/digispark/images/m/oak-prototype-shield-3.jpg|{{https://s3.amazonaws.com/digispark/images/t/oak-prototype-shield-3.jpg}}]]
[[https://s3.amazonaws.com/digispark/images/m/oak-prototype-shield-6.jpg|{{https://s3.amazonaws.com/digispark/images/t/oak-prototype-shield-6.jpg}}]]


Cut or Snap a length of two male headers 9 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin.

**Tip:** Inserting the headers into a breadboard and then placing the board on top can make this process easier. Be caureful not to heat the headerpins to the point that it melts the plastic surrounding the pin or the breadboard.

[[https://s3.amazonaws.com/digispark/images/m/oak-prototype-shield-7.jpg|{{https://s3.amazonaws.com/digispark/images/t/oak-prototype-shield-7.jpg}}]]
[[https://s3.amazonaws.com/digispark/images/m/oak-prototype-shield-8.jpg|{{https://s3.amazonaws.com/digispark/images/t/oak-prototype-shield-8.jpg}}]]

**Tip 2:** If not using the above tip, solder one pin then check that the header is in the right position and is square to the PCB before continuing the rest.

[[https://s3.amazonaws.com/digispark/images/m/oak-prototype-shield-10.jpg|{{https://s3.amazonaws.com/digispark/images/t/oak-prototype-shield-10.jpg}}]]
[[https://s3.amazonaws.com/digispark/images/m/oak-prototype-shield-5.jpg|{{https://s3.amazonaws.com/digispark/images/t/oak-prototype-shield-5.jpg}}]]


**Note:** If you are using stackable headers, use them here instead of the standard male headers.
Digistump Wiki

User Tools

Site Tools

Page Tools
