User Tools

Site Tools


oak:tutorials:proto

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Last revision Both sides next revision
oak:tutorials:proto [2016/01/17 18:24]
briankb
oak:tutorials:proto [2016/01/17 18:51]
briankb added photo links
Line 4: Line 4:
  
 =====Product Description:​===== =====Product Description:​=====
-[IMAGE SHIELD + MALE HEADERS with Ruler+[[https://​s3.amazonaws.com/​digispark/​images/​m/​oak-prototype-shield-1.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​oak-prototype-shield-1.jpg}}]
-[IMAGE SHIELD CLOSEUP with Ruler+[[https://​s3.amazonaws.com/​digispark/​images/​m/​oak-prototype-shield-2.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​oak-prototype-shield-2.jpg}}]
-[ASSEMBLED CLOSEUP]+[[https://​s3.amazonaws.com/​digispark/​images/​m/​oak-prototype-shield-4.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​oak-prototype-shield-4.jpg}}]
  
 The Prototype Shield Kit breaks out the connections on the Digistump Oak development board and provides a small through hole soldering area for building custom circuits. The Prototype Shield Kit breaks out the connections on the Digistump Oak development board and provides a small through hole soldering area for building custom circuits.
Line 29: Line 30:
 =====Assembly:​===== =====Assembly:​=====
  
-[IMAGE SHIELD + MALE HEADERS with Ruler]+[[https://​s3.amazonaws.com/​digispark/​images/​m/​oak-prototype-shield-3.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​oak-prototype-shield-3.jpg}}]
 +[[https://​s3.amazonaws.com/​digispark/​images/​m/​oak-prototype-shield-6.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​oak-prototype-shield-6.jpg}}]] 
  
 Cut or Snap a length of two male headers 9 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin. Cut or Snap a length of two male headers 9 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin.
Line 35: Line 38:
 **Tip:** Inserting the headers into a breadboard and then placing the board on top can make this process easier. Be caureful not to heat the headerpins to the point that it melts the plastic surrounding the pin or the breadboard. **Tip:** Inserting the headers into a breadboard and then placing the board on top can make this process easier. Be caureful not to heat the headerpins to the point that it melts the plastic surrounding the pin or the breadboard.
  
-**Tip 2:** If not using the above tip, solder one pin then check that the header is in the right position and is square to the PCB before continuing the rest.+[[https://s3.amazonaws.com/​digispark/​images/​m/​oak-prototype-shield-7.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​oak-prototype-shield-7.jpg}}]] 
 +[[https://​s3.amazonaws.com/​digispark/​images/​m/​oak-prototype-shield-8.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​oak-prototype-shield-8.jpg}}]]
  
-[ASSEMBLED CLOSEUP]+**Tip 2:** If not using the above tip, solder one pin then check that the header is in the right position and is square to the PCB before continuing the rest.
  
 +[[https://​s3.amazonaws.com/​digispark/​images/​m/​oak-prototype-shield-10.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​oak-prototype-shield-10.jpg}}]]
 +[[https://​s3.amazonaws.com/​digispark/​images/​m/​oak-prototype-shield-5.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​oak-prototype-shield-5.jpg}}]]
  
  
 **Note:** If you are using stackable headers, use them here instead of the standard male headers. **Note:** If you are using stackable headers, use them here instead of the standard male headers.
oak/tutorials/proto.txt · Last modified: 2016/02/19 17:50 by digistump