Digistump Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
===== Oak: PIR Motion Sensor =====

====== Tutorial Complete - Adding Connection piece soon======

{{http://digistump.com/wiki/_media/oak/tutorials/pir_sketch.png?300|
{{http://digistump.com/wiki/_media/oak/tutorials/pir_sketch.png?600|}}


If you've been working your way though the starter tutorials to get here, you've found that there are many different kinds of sensors readily available for your Oak, each with their own benefits. The PIR sensor (Passive Infrared Sensor) works by detecting infrared (invisible radiant) energy, aka heat. These are most commonly knows as the security sensor tucked up inside the corners inside homes to detect intruders.


===== Components used =====

^ Part       ^ Quantity          ^Identification^
| Oak with soldered headers |1| |
| PIR HC-SR501 |1| |
| Jumper Wires |3| |


===== Concepts =====

=== Connecting to other products and apps ===

Process:
Create ifttt acct
Connect ifttt to Particle & gmail
Create IF recipe
   * Start with particle - define event name and event contents
   * define gmail info

=== Research Your Sensors ===

My particular HC-SR501 states that it operates with 4.5 - 20v. However taking a deeper look, the chipset's datasheet states it runs on 3.3v. The 5v input goes to the board's power regulator, which shifts it to 3.3v. There is a bypass pin that allows one to power the sensor directly with 3.3v. This is why the power jumper does not go to the bottom sensor input. See the pictures below for more detail.

===== Circuit =====

3 connections total from the Sensor to the Oak, the VCC, GND, and Output. The power from the Oak is going to the 3.3v pin NOT the 5v pin that is beside the Output pin.

  *      =Connect the 3.3 vcc pin to the Oak VCC=
  *      Connect GND pin to the Oak GND
  *      Connect the Output pin to Oak pin #2


**NOTE** The schematic reflects the location of the pins with the sensor FACING you due to the model showing the sensor face.

{{http://digistump.com/wiki/_media/oak/tutorials/pir_sketch.png?300|
{{http://digistump.com/wiki/_media/oak/tutorials/pir_sketch.png?600|}}
     

Here are picture of the actual setup. The 1st is a closeup of the rear of the sensor showing the 3.3v connection. The 2nd is of course the entire setup.

{{http://digistump.com/wiki/_media/oak/tutorials/pir_sensor_back2.jpg?300|
{{http://digistump.com/wiki/_media/oak/tutorials/pir_sensor_back2.jpg?600|}}

{{http://digistump.com/wiki/_media/oak/tutorials/pir_sensor_hook-up.jpg?300|
{{http://digistump.com/wiki/_media/oak/tutorials/pir_sensor_hook-up.jpg?600|}}


===== Code =====

If you've been doing the starter tutorials, this code should be 2nd nature to you. The lines that aren't typical from the starter tutorials have been commented. The onboard LED is used to signal at the device that motion was detected.

The take away from this will be you creating a free ifttt.com account, and connecting it to your Particle account.

<code>

int calibrationTime = 30;        
long unsigned int lowIn;         
long unsigned int pause = 5000;  

boolean lockLow = true;
boolean takeLowTime;  

int pirPin = 2; 
int ledPin = 1;


void setup(){
  
  pinMode(pirPin, INPUT);
  pinMode(ledPin, OUTPUT);
  digitalWrite(pirPin, LOW);

  //give the sensor some time to calibrate
    for(int i = 0; i < calibrationTime; i++){
      delay(10000);
      }
    delay(50);
  }

void loop(){

     if(digitalRead(pirPin) == HIGH){
       digitalWrite(ledPin, HIGH);
       Particle.publish("motion-detected"); // use Particle.publish most basic form, one argument
         if(lockLow){  
         lockLow = false;            
         delay(1000);
         }         
         takeLowTime = true;
       }

     if(digitalRead(pirPin) == LOW){       
       digitalWrite(ledPin, LOW);  

       if(takeLowTime){
        lowIn = millis();      
        takeLowTime = false;      
        }

       if(!lockLow && millis() - lowIn > pause){  
           //makes sure this block of code is only executed again after 
           //a new motion sequence has been detected
           lockLow = true;                        
           delay(50);
           }
       }
  }
</code>



===== Conclusion =====

Connecting your Oak to Particle, (and thereby OakTerm) gives you a number of options, the ability to view what your Oak is doing, program your Oak through the Particle IDE, and event put it into Config Mode via OakTerm. Using a system like ifttt.com quickly, and easily extends the capability of your Oak.

With the various devices available, with varying voltages, it's not uncommon for manufacturers to market and build to a specific voltage only. This doesn't mean that it won't work, sometimes with minor modifications, with something else. If your up for it, do further research to see what you can do with some tweeking, at your own risk, and the risk of your equipment of course.

The PIR sensors are used of course as part of security systems, as well as the automatic room lights. What project will you use a PIR sensor for? Write one up and post it on the digistump Oak forums.
Digistump Wiki

User Tools

Site Tools

Page Tools
