Digistump Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.

=====THIS TUTORIAL HAS NOT YET BEEN REVIEWED, PLEASE DO NOT USE UNTIL IT HAS======

======Oak OLED Shield Kit Tutorial======

=====Product Description:=====
[[https://s3.amazonaws.com/digispark/images/m/oak-oled-shield-1.JPG|{{https://s3.amazonaws.com/digispark/images/t/oak-oled-shield-1.JPG}}]]
[[https://s3.amazonaws.com/digispark/images/m/oak-oled-shield-6.JPG|{{https://s3.amazonaws.com/digispark/images/t/oak-oled-shield-6.JPG}}]]

The Oak OLED Shield Kit allows you to build a shield that adds a 0.93" white on black 128x64 pixel OLED screen to the Oak. The screen is controlled via I2C. Use it to see what your project is thinking, your favorite Twitter feed in bite-size form, or whatever you drum up!

This is an unassembled kit and requires basic soldering. This is designed for use with the Digispark Oak development board, which is not included.  This kit includes the SSD1306 controlled Monochrome 0.96" 128x64 OLED.

=====Parts:=====

^ Part       ^ Quantity          ^Identification^
| Oak Combo PCB|1| |
| 4.7K (4K7) Ohm 1/4W resistor 1% or 5%|2| Yellow - Violet - Red|
| I2C OLED Module |1| |
| 1x40pin male 0.1" pitch header| 21 pins worth| |


**Resistor Values:** For more information on how to identify the value of the resistors we recommend these sites:
A nice simple resistor calculator: http://www.ealnet.com/m-eal/resistor/resistor.htm
A comprehensive article on identification: http://www.diyaudioandvideo.com/Electronics/Color/

**Soldering:** If you are new to soldering we recommend the following tutorials:
Soldering Basics (http://www.sparkfun.com/tutorials/106) and Soldering Crash Course from the folks at Sparkfun (http://www.sparkfun.com/tutorials/354).
How to solder from the Curious Inventor: http://store.curiousinventor.com/guides/How_to_Solder

Adafruit has this excellent guide that starts with the tools needed and then shows detailed pictures, including some of the common problems that beginners experience (http://learn.adafruit.com/adafruit-guide-excellent-soldering)

**We assume for these assembly instructions that you know the basics of thru-hole soldering. If you don't check out the links above, these boards are very easy to solder - we promise!**


=====Assembly:=====

**NOTE:** Before you start: If you have a multimeter check for shorts between the GND pin hole and the other pin holes - if you find any please send us an email at support at digistump dot com and we will replace the board.

[[https://s3.amazonaws.com/digispark/images/m/oak-oled-shield-1.JPG|{{https://s3.amazonaws.com/digispark/images/t/oak-oled-shield-1.JPG}}]]

Solder resistors one at a time. Solder the leads and clip off the excess. Repeat for both resistors.

[[https://s3.amazonaws.com/digispark/images/m/oak-oled-shield-2.JPG|{{https://s3.amazonaws.com/digispark/images/t/oak-oled-shield-2.JPG}}]]


Cut two lengths of male headers each 9 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin.

**WARNING!** Ensure you do not solder one of the 9 pin set of male headers on the row with the arrows pointing to the row described as "PRO SHIELD USE ONLY". You will need to solder it into the row of holes in the middle of the board with "GND" on one end and "EN" on the other.

**Tip:** Inserting the headers into a breadboard and then placing the board on top can make this process easier.

**Note:** If you are using stackable headers, use them here instead of the standard male headers.

[[https://s3.amazonaws.com/digispark/images/m/oak-oled-shield-3.JPG|{{https://s3.amazonaws.com/digispark/images/t/oak-oled-shield-3.JPG}}]]

Insert the OLED module into the front of the board matching the pins labeled for the OLED module. Solder the pins on the back, optionally snip off the excess.

[[https://s3.amazonaws.com/digispark/images/m/oak-oled-shield-4.JPG|{{https://s3.amazonaws.com/digispark/images/t/oak-oled-shield-4.JPG}}]]

[[https://s3.amazonaws.com/digispark/images/m/oak-oled-shield-5.JPG|{{https://s3.amazonaws.com/digispark/images/t/oak-oled-shield-5.JPG}}]]

Your Oak OLED shield is complete!

=====Programming:=====
Digistump Wiki

User Tools

Site Tools

Page Tools
