Differences

This shows you the differences between two versions of the page.

--- oak:tutorials:lipo [2016/03/24 15:37]
zeiv [Assembly:]
+++ oak:tutorials:lipo [2016/04/13 12:20]
zeiv [THIS TUTORIAL HAS NOT YET BEEN REVIEWED, PLEASE DO NOT USE UNTIL IT HAS]
@@ Line 1: / Line 1: @@
-====== THIS TUTORIAL HAS NOT YET BEEN REVIEWED, PLEASE DO NOT USE UNTIL IT HAS ======
 ====== LiPo Charger Shield Tutorial ======
@@ Line 36: / Line 35: @@
 {{:oak:tutorials:photo_mar_24_1_20_13_pm.jpg?500|}}
-The LiPo Shield PCB thru-holes we will be using for the Oak are the 2-pin battery connector and the 3-pin male header for VCC/GND/VIN.  The other thru-holes (for 2-pin and 6-pin headers) are for compatibility with other Digistump development boards. **NEEDS VERIFICATION**
+The LiPo Shield PCB thru-holes we will be using for the Oak are the 2-pin JST battery connector and the 3-pin male header for VCC/GND/VIN.  The included 6-pin header is for stability only, therefore stackable headers in the corresponding thru-holes are recommended. The 6-pin headers may safely be omitted. The set of 2 thru-holes are for an optional switch or jumper (see below).
 {{:oak:tutorials:photo_mar_24_1_24_34_pm.jpg?500|}}
-The thru-holes for the 2-pin battery connector are slightly smaller than the others.  Notice how there are three holes for the 2-pin connector.  This allows you to mount the connector either on the bottom or the top of the PCB.  Pay careful attention to the labels on the PCB to determine which thru-holes to use for the 2-pin connecter.
+The thru-holes for the 2-pin JST battery connector are slightly smaller than the others.  Notice how there are three holes for the 2-pin connector.  This allows you to mount the connector either on the bottom or the top of the PCB.  Pay careful attention to the labels on the PCB to determine which thru-holes to use for the 2-pin connector.  The JST battery connector may be mounted on the bottom if you wish to solder the Oak's 3-pin power header on upside-down, thereby allowing the user to plug in the LiPo shield underneath the Oak in order not to block the other pins.
 {{:oak:tutorials:photo_mar_24_1_24_10_pm.jpg?500|}}
-**IMPORTANT NOTE:** It is highly recommended that the 2-pin connecter be mounted on the //top// of the PCB.  The Oak's included female headers would obstruct the connect if mounted on the bottom.
+**IMPORTANT NOTE:** It is highly recommended that the 2-pin connecter be mounted on the //top// of the PCB if you have already solder the Oak's 3-pin power header to its top.  The Oak's included female headers would obstruct the battery connector if mounted on the bottom.
 Solder the 2-pin JST connecter and 3-pin male header onto the PCB as pictured.
@@ Line 51: / Line 50: @@
 {{:oak:tutorials:photo_mar_24_2_05_55_pm.jpg?500|}}
-Connect the LiPo shield to the Oak's 3-pin VCC/GND/VIN female header.  Then plug in the battery to the LiPo Shield 2-pin connecter and connect the Oak's USB power to charge.  The include LiPo battery ships with some charge, but will still need to charge for about an hour.
+Connect the LiPo shield to the Oak's 3-pin VCC/GND/VIN female header.  Then plug in the battery to the LiPo Shield 2-pin connecter and connect the Oak's USB power to charge.  The include LiPo battery ships with some charge, but will still need to charge for about an hour.  The red LED on the LiPo shield will turn off when the battery is fully charged.
 {{:oak:tutorials:photo_mar_24_2_02_16_pm.jpg?500|}}
@@ Line 63: / Line 62: @@
 {{:oak:tutorials:photo_mar_24_1_25_46_pm.jpg?500|}}
+===== Adding a Switch =====
+Optionally, a switch or jumper (not included) may be soldered to the LiPo shield PCB via the thru-holes to the left of the 3-pin power header. When the switch is closed, power will be off.
 =====Usage:=====

Digistump Wiki

User Tools

Site Tools

Differences

Page Tools