User Tools

Site Tools


oak:tutorials:levelshift

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
oak:tutorials:levelshift [2016/02/19 17:55]
digistump
oak:tutorials:levelshift [2016/03/21 16:17] (current)
digistump [Using the Oak Level Shifter:]
Line 13: Line 13:
    * 5V output with pinout optimized for a WS2811/2812 LED strip    * 5V output with pinout optimized for a WS2811/2812 LED strip
    * 5V input to the ADC pin    * 5V input to the ADC pin
 +
  
 This is an unassembled kit and requires basic soldering skills. This shield is designed for use with the Digistump Oak development board (not included). Make sure all parts listed below have been provided before proceeding. This is an unassembled kit and requires basic soldering skills. This shield is designed for use with the Digistump Oak development board (not included). Make sure all parts listed below have been provided before proceeding.
Line 19: Line 20:
 [[https://​s3.amazonaws.com/​digispark/​images/​m/​oak-level-shifter-shield-1.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​oak-level-shifter-shield-1.jpg}}]] [[https://​s3.amazonaws.com/​digispark/​images/​m/​oak-level-shifter-shield-1.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​oak-level-shifter-shield-1.jpg}}]]
 [[https://​s3.amazonaws.com/​digispark/​images/​m/​oak-level-shifter-shield-2.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​oak-level-shifter-shield-2.jpg}}]] [[https://​s3.amazonaws.com/​digispark/​images/​m/​oak-level-shifter-shield-2.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​oak-level-shifter-shield-2.jpg}}]]
- 
  
 ===== Parts: ===== ===== Parts: =====
Line 140: Line 140:
 Whatever voltage is supplied to the Oak Level Shifter shield VIN is distributed (directly connected) to each of the Level Shifter shield pins labeled 5V. As such, all external devices connected to pins labeled 5V will receive the actual VIN supply voltage. Whatever voltage is supplied to the Oak Level Shifter shield VIN is distributed (directly connected) to each of the Level Shifter shield pins labeled 5V. As such, all external devices connected to pins labeled 5V will receive the actual VIN supply voltage.
  
-Oak regulates VIN supplied at either of the Oak's VIN pins for use by Oak, but will pass through VIN supplied at the Oak's VIN 4.5-12V tolerant pin to the Oak Level Shifter shield VIN pin. Therefore, the Oak's VIN pin if used to supply voltage to the Oak (not recommended when using the Oak Level Shifter shield) should be limited to recommended ratings for level shifter IC (5V). +Oak regulates VIN supplied at either of the Oak's VIN pins for use by Oak, but will pass through VIN supplied at the Oak's VIN 4.5-12V tolerant pin to the Oak Level Shifter shield VIN pin. Therefore, the Oak's VIN pin if used to supply voltage to the Oak (not recommended when using the Oak Level Shifter shield) should be limited to recommended ratings for level shifter IC (5V).
  
 +//**Pinout Correction for the P1 Servo Header:**//
  
 +The pins labeled GND and P1 for the center servo header on the level shifter are reversed. GND is actually P1 and P1 is actually GND. This only applies to the servo header that uses P1 for signal output.
 +{{ :​oak:​tutorials:​oak-level-shifter-shield-24.jpg?​direct&​300 |}}
  
 +//** Using with bi-directional sensors: **//
  
 +Since the level shifter IC used on this level shifter is not an automatic bi-directional level shifter, if you  you wish to use bi-directional sensors such as the popular OneWire DS18B20, you will need to use the I2C pins on the shield. SDA is P0 on the Oak, and SCL is P2. 
oak/tutorials/levelshift.1455933336.txt.gz · Last modified: 2016/02/19 17:55 by digistump