oak:tutorials:bluetooth
Differences
This shows you the differences between two versions of the page.
| Last revision Both sides next revision | |||
|
oak:tutorials:bluetooth [2016/02/25 14:12] healthyfatboy created |
oak:tutorials:bluetooth [2016/03/10 22:45] digistump |
||
|---|---|---|---|
| Line 5: | Line 5: | ||
| =====Product Description:===== | =====Product Description:===== | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/oak-bt-shield-1.jpg|{{https://s3.amazonaws.com/digispark/images/t/oak-bt-shield-1.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/oak-bt-shield-1.JPG|{{https://s3.amazonaws.com/digispark/images/t/oak-bt-shield-1.JPG}}]] |
| - | [[https://s3.amazonaws.com/digispark/images/m/oak-bt-shield-4.jpg|{{https://s3.amazonaws.com/digispark/images/t/oak-bt-shield-4.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/oak-bt-shield-4.JPG|{{https://s3.amazonaws.com/digispark/images/t/oak-bt-shield-4.JPG}}]] |
| Line 37: | Line 37: | ||
| Empty kit bag (or if using a raw PCB, acquire parts) and verify contents. | Empty kit bag (or if using a raw PCB, acquire parts) and verify contents. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/oak-bt-shield-1.jpg|{{https://s3.amazonaws.com/digispark/images/t/oak-bt-shield-1.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/oak-bt-shield-1.JPG|{{https://s3.amazonaws.com/digispark/images/t/oak-bt-shield-1.JPG}}]] |
| Insert 6 pin right angle socket into top of PCB - insert it into the set of 6 holes that say "BT" next to them - this is the set at the bottom edge of the board. The row above shows "BLE" but do not solder to that set of rows! Solder socket pins on the bottom of the board. | Insert 6 pin right angle socket into top of PCB - insert it into the set of 6 holes that say "BT" next to them - this is the set at the bottom edge of the board. The row above shows "BLE" but do not solder to that set of rows! Solder socket pins on the bottom of the board. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/oak-bt-shield-2.jpg|{{https://s3.amazonaws.com/digispark/images/t/oak-bt-shield-2.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/oak-bt-shield-2.JPG|{{https://s3.amazonaws.com/digispark/images/t/oak-bt-shield-2.JPG}}]] |
| Cut two lengths of male headers each 9 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin on the top. | Cut two lengths of male headers each 9 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin on the top. | ||
| Line 51: | Line 51: | ||
| **Note:** If you are using stackable headers, use them here instead of the standard male headers. | **Note:** If you are using stackable headers, use them here instead of the standard male headers. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/oak-bt-shield-3.jpg|{{https://s3.amazonaws.com/digispark/images/t/oak-bt-shield-3.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/oak-bt-shield-3.JPG|{{https://s3.amazonaws.com/digispark/images/t/oak-bt-shield-3.JPG}}]] |
| Insert the HC-05 Bluetooth breakout module into the 6 pin socket as shown. The 4 pins of the module will go into the center 4 pins of the socket. | Insert the HC-05 Bluetooth breakout module into the 6 pin socket as shown. The 4 pins of the module will go into the center 4 pins of the socket. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/oak-bt-shield-4.jpg|{{https://s3.amazonaws.com/digispark/images/t/oak-bt-shield-4.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/oak-bt-shield-4.JPG|{{https://s3.amazonaws.com/digispark/images/t/oak-bt-shield-4.JPG}}]] |
| Your Oak Bluetooth Classic shield is complete! | Your Oak Bluetooth Classic shield is complete! | ||
oak/tutorials/bluetooth.txt · Last modified: 2016/03/10 22:47 by digistump
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
