oak:tutorials:beta
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
oak:tutorials:beta [2016/01/07 15:16] digistump |
oak:tutorials:beta [2016/01/08 00:00] defragster [Parts:] (4) 1K not 2K resistors |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| =====Product Description:===== | =====Product Description:===== | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/oakbeta1.jpg|{{https://s3.amazonaws.com/digispark/images/t/oakbeta1.jpg}}]][[https://s3.amazonaws.com/digispark/images/m/oakbeta2.jpg|{{https://s3.amazonaws.com/digispark/images/t/oakbeta2.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/oakbeta1.jpg|{{https://s3.amazonaws.com/digispark/images/t/oakbeta1.jpg}}]][[https://s3.amazonaws.com/digispark/images/m/oakbeta2.JPG|{{https://s3.amazonaws.com/digispark/images/t/oakbeta2.JPG}}]] |
| The Oak Beta Alarm Clock Kit connects a 2.2" TFT LCD, 5 way joystick, and buzzer with a Oak development board. This allows the Oak to act as a WiFi connected alarm clock, among other things. | The Oak Beta Alarm Clock Kit connects a 2.2" TFT LCD, 5 way joystick, and buzzer with a Oak development board. This allows the Oak to act as a WiFi connected alarm clock, among other things. | ||
| Line 15: | Line 15: | ||
| | 2.2" TFT LCD with SD Card Slot|1| | | | 2.2" TFT LCD with SD Card Slot|1| | | ||
| | 2N3904 NPN Transistor|1| | | | 2N3904 NPN Transistor|1| | | ||
| - | | 1k Ohm 1/4W 5% Resistor (previously 10k)|4| Brown - Black - Red | | + | | 1k Ohm 1/4W 5% Resistor (silkscreen shows 2k)|4| Brown - Black - Red | |
| | 10k Ohm 1/4W 5% Resistor (previously 10k)|2| Brown - Black - Orange | | | 10k Ohm 1/4W 5% Resistor (previously 10k)|2| Brown - Black - Orange | | ||
| | 47 Ohm 1/4W 5% Resistor (previously 10k)|1| Yellow - Violet - Black | | | 47 Ohm 1/4W 5% Resistor (previously 10k)|1| Yellow - Violet - Black | | ||
| Line 38: | Line 38: | ||
| Insert resistors into the locations labeled for each value. NOTE: The 1K Resistors should be placed in the 2K locations. Solder the leads and clip off the excess. | Insert resistors into the locations labeled for each value. NOTE: The 1K Resistors should be placed in the 2K locations. Solder the leads and clip off the excess. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/oakbeta3.jpg|{{https://s3.amazonaws.com/digispark/images/t/oakbeta3.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/oakbeta3.JPG|{{https://s3.amazonaws.com/digispark/images/t/oakbeta3.JPG}}]] |
| Insert the transistor, matching the shape with the printing on the board. Solder the leads and clip off excess. | Insert the transistor, matching the shape with the printing on the board. Solder the leads and clip off excess. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/oakbeta4.jpg|{{https://s3.amazonaws.com/digispark/images/t/oakbeta4.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/oakbeta4.JPG|{{https://s3.amazonaws.com/digispark/images/t/oakbeta4.JPG}}]] |
| Insert the buzzer, with the + sign on the buzzer matching the one on the board. Solder the two pins. | Insert the buzzer, with the + sign on the buzzer matching the one on the board. Solder the two pins. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/oakbeta5.jpg|{{https://s3.amazonaws.com/digispark/images/t/oakbeta5.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/oakbeta5.JPG|{{https://s3.amazonaws.com/digispark/images/t/oakbeta5.JPG}}]] |
| Insert the 5 way joystick, notice that the pins are closer together on one end and match the holes on the board. Solder the pins. | Insert the 5 way joystick, notice that the pins are closer together on one end and match the holes on the board. Solder the pins. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/oakbeta6.jpg|{{https://s3.amazonaws.com/digispark/images/t/oakbeta6.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/oakbeta6.JPG|{{https://s3.amazonaws.com/digispark/images/t/oakbeta6.JPG}}]] |
| Cut two length of male headers 9 pins long and one 4 pins long. Insert into corresponding positions (9 pins on the bottom of the board, 4 pin on top) and solder each pin. | Cut two length of male headers 9 pins long and one 4 pins long. Insert into corresponding positions (9 pins on the bottom of the board, 4 pin on top) and solder each pin. | ||
| Line 58: | Line 58: | ||
| **Tip:** Inserting the headers into a breadboard and then placing the board on top can make this process easier. | **Tip:** Inserting the headers into a breadboard and then placing the board on top can make this process easier. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/oakbeta7.jpg|{{https://s3.amazonaws.com/digispark/images/t/oakbeta7.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/oakbeta7.JPG|{{https://s3.amazonaws.com/digispark/images/t/oakbeta7.JPG}}]] |
| - | Insert the LCD screen on top of the shield to that it aligns with the 4 pins you soldered in the last step, and the other pins on the LCD align with the holes. Solder the 4 pins to the LCD and the other pins to the back of the shield. | + | Insert the LCD screen on top of the shield to that it aligns with the 4 pins you soldered in the last step, and the other pins on the LCD align with the holes. Ensure the SD Card slot on the bottom of the LCD is not touching the pins below it on the shield - sticking a spare piece of headers between them during soldering can ensure a gap is left. Solder the 4 pins to the LCD and the other pins to the back of the shield. |
| - | [[https://s3.amazonaws.com/digispark/images/m/oakbeta8.jpg|{{https://s3.amazonaws.com/digispark/images/t/oakbeta8.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/oakbeta8.JPG|{{https://s3.amazonaws.com/digispark/images/t/oakbeta8.JPG}}]] |
| Plug shield into Oak. | Plug shield into Oak. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/oakbeta2.jpg|{{https://s3.amazonaws.com/digispark/images/t/oakbeta2.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/oakbeta2.JPG|{{https://s3.amazonaws.com/digispark/images/t/oakbeta2.JPG}}]] |
| =====Programming:===== | =====Programming:===== | ||
oak/tutorials/beta.txt · Last modified: 2016/01/08 00:00 by defragster
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
