Differences

This shows you the differences between two versions of the page.

--- digispark:tutorials:rgb [2013/03/29 07:06]
PeterMortensen [Parts:] Unit symbols (e.g. A) are in uppercase, but not if spelled out (ampere).
+++ digispark:tutorials:rgb [2015/06/03 00:23]
oscomputing [Programming:]
@@ Line 34: / Line 34: @@
-Empty kit bag (or if using a raw PCB, aquire parts) and verify contents.
+Empty kit bag (or if using a raw PCB, acquire parts) and verify contents.
 **Note for Kickstarter Backers and Pre-orders:** Headers are not included in each kit bag, but the entire order came with more than enough headers for all kits.
@@ Line 43: / Line 43: @@
 [[https://s3.amazonaws.com/digispark/images/m/rgb5.jpg|{{https://s3.amazonaws.com/digispark/images/t/rgb5.jpg}}]]
-When inserting the LED into the board ensure the longest lead of the LED goes through the hole marked ground - this ensure you ahve the LED oriented properly. Solder the LED leads and clip off the excess.
+When inserting the LED into the board ensure the longest lead of the LED goes through the hole marked ground - this will ensure you have the LED oriented properly. Solder the LED leads and clip off the excess.
 [[https://s3.amazonaws.com/digispark/images/m/rgb4.jpg|{{https://s3.amazonaws.com/digispark/images/t/rgb4.jpg}}]]
-Cut a length of male headers 6 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin.
+Cut two lengths of male headers, one 6 pins long and another 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin.
-**Tip:** Inseting the headers into a breadboard and then placing the board on top can make this process easier.
+**Tip:** Inserting the headers into a breadboard and then placing the board on top can make this process easier.
 **Note:** If you are using stackable headers, use them here instead of the standard male headers.
@@ Line 63: / Line 63: @@
 =====Programming:=====
-**Note:** The programming sections assumes you've installed the Arduino IDE and the Digispark Add-ons: [[digispark:tutorials:connecting|Connecting and Programming Your Digispark]]
+**Note:** The programming sections assumes you've installed the Arduino IDE and the Digispark Add-ons: [[digispark:tutorials:connecting|Connecting and Programming Your Digispark]].
-The RGB shield uses the following pins to control the LEDS:
+The RGB shield uses the following pins to control the LEDs:
-Pin 0 -> Red
+Pin 0 -> Red LED
-Pin 1 -> Green
+Pin 1 -> Green LED
-Pin 2 -> Blue
+Pin 2 -> Blue LED
 Turning a color on or off is as simple as this:
 <code arduino>
 void setup() {
-  // initialize the LED pins as outputs
+    // Initialize the LED pins as outputs
-  pinMode(0, OUTPUT);
+    pinMode(0, OUTPUT);
-  pinMode(1, OUTPUT);
+    pinMode(1, OUTPUT);
-  pinMode(2, OUTPUT);
+    pinMode(2, OUTPUT);
 }
 void loop() {
-  digitalWrite(0, HIGH);   	// turn the Red LED On
+    digitalWrite(0, HIGH);  // Turn the red LED On
-  delay(1000);              // wait for a second
+    delay(1000);            // Wait for a second
-  digitalWrite(1, HIGH);   	// turn the Green LED On
+    digitalWrite(1, HIGH);  // Turn the green LED On
-  delay(1000);              // wait for a second
+    delay(1000);            // Wait for a second
-  digitalWrite(2, HIGH);   	// turn the Blue LED On
+    digitalWrite(2, HIGH);  // Turn the blue LED On
-  delay(1000);              // wait for a second
+    delay(1000);            // Wait for a second
-  digitalWrite(0, LOW);    	// turn the Red LED off
+    digitalWrite(0, LOW);   // Turn the red LED off
-  digitalWrite(1, LOW);     // turn the Green LED off
+    digitalWrite(1, LOW);   // Turn the green LED off
-  digitalWrite(2, LOW);     // turn the Blue LED off
+    digitalWrite(2, LOW);   // Turn the blue LED off
-  delay(1000);              // wait for a second
+    delay(1000);            // Wait for one second
 }
 </code>
-**PWM Note:** While Red and green are connected to pins that support PWM, Blue is not - this is because the 3rd PWM pin is used by the USB communications and we figure most will want to use the RGB shield with USB communication. See Examples->DigisparkRGB->DigisparkRGB or Examples->DigisparkUSB->DigiBlink for examples of using software PWM for pin 2 (Blue).
+**PWM Note:** While the red and green LEDs are connected to pins that support PWM, the blue LED is not - this is because the third PWM pin is used by the USB communications and we figure most will want to use the RGB shield with USB communication. See Examples->DigisparkRGB->DigisparkRGB or Examples->DigisparkUSB->DigiBlink for examples of using software PWM for pin 2 (blue LED).
-If you are not planning to use USB communication: If you want to connect blue to P4 instead of P2 - flip the shield over and you'll see two solder jumpers, one has a little trace connecting its two pads, the other does't - cut the one with the trace and bridge the other with solder this will disconnect blue from P2 and connect it to P4.
+If you are not planning to use USB communication: If you want to connect the blue LED to P4 instead of P2 - flip the shield over and you'll see two solder jumpers, one has a little trace connecting its two pads, the other doesn't - cut the one with the trace and bridge the other with solder. This will disconnect the blue LED from P2 and connect it to P4.
+In the Arduino IDE, take a look at the Examples -> DigisparkRGB -> DigisparkRGB example for more advanced usage. When using that example you must set your board type as Digispark (Tiny Core) for it to work.
-Take a look at the Examples->DigisparkRGB->DigisparkRGB example for more advanced usage. When using that example you must set your board type as Digispark (Tiny Core) for it to work.

Digistump Wiki

User Tools

Site Tools

Differences

Page Tools