digispark:tutorials:prowifi
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
digispark:tutorials:prowifi [2014/12/10 13:17] digistump |
digispark:tutorials:prowifi [2015/02/17 18:53] digistump |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | Tutorial coming shortly - for those attempting on their own - please note: the wifi module goes on the bottom of the shield, not the top. | ||
| - | |||
| ======Pro WiFi Shield Kit Tutorial====== | ======Pro WiFi Shield Kit Tutorial====== | ||
| =====Product Description:===== | =====Product Description:===== | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/wifi.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi.JPG}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/wifi1.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi1.JPG}}]] |
| - | [[https://s3.amazonaws.com/digispark/images/m/wifi.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi.JPG}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/wifi11.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi11.JPG}}]] |
| This is an unassembled kit and requires basic soldering. This is designed for use with the Digispark development board, which is not included. | This is an unassembled kit and requires basic soldering. This is designed for use with the Digispark development board, which is not included. | ||
| Line 36: | Line 34: | ||
| =====Assembly:===== | =====Assembly:===== | ||
| + | |||
| + | **NOTE:** Before you start: If you have a multimeter check for shorts between the GND pin hole and the other pin holes - if you find any please send us an email at support at digistump dot com and we will replace the board. | ||
| Check the contents of your kit and ensure you have all of the parts listed. | Check the contents of your kit and ensure you have all of the parts listed. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/wifi.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi.JPG}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/wifi1.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi1.JPG}}]] |
| + | |||
| + | |||
| + | Insert the 4.7K and 10K resistors into the spots labeled for them. Solder the leads on the bottom of the board and clip off any excess. | ||
| + | |||
| + | [[https://s3.amazonaws.com/digispark/images/m/wifi2.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi2.JPG}}]] | ||
| Insert the 3.3v regulator, matching it with the outline on the board. Solder the leads on the bottom of the board and clip off any excess. | Insert the 3.3v regulator, matching it with the outline on the board. Solder the leads on the bottom of the board and clip off any excess. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/wifi.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi.JPG}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/wifi3.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi3.JPG}}]] |
| Insert the 10uf Capacitor - ensuring the lead on the side of the capacitor that is labeled with a grey stripe and minus signs is going into the hole that DOES NOT have the plus sign next to it. Solder the leads on the bottom of the board and clip off any excess. | Insert the 10uf Capacitor - ensuring the lead on the side of the capacitor that is labeled with a grey stripe and minus signs is going into the hole that DOES NOT have the plus sign next to it. Solder the leads on the bottom of the board and clip off any excess. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/wifi.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi.JPG}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/wifi4.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi4.JPG}}]] |
| Insert the 0.1uf capacitor as shown (lead orientation doesn't matter). Solder the leads on the bottom of the board and clip off any excess. | Insert the 0.1uf capacitor as shown (lead orientation doesn't matter). Solder the leads on the bottom of the board and clip off any excess. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/wifi.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi.JPG}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/wifi5.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi5.JPG}}]] |
| - | + | ||
| - | Insert the 4.7K and 10K resistors into the spots labeled for them. Solder the leads on the bottom of the board and clip off any excess. | + | |
| - | + | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/wifi.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi.JPG}}]] | + | |
| Insert the WiFi module as shown - into the bottom of the PCB (NOT THE TOP!) - solder the leads on the top of the board. | Insert the WiFi module as shown - into the bottom of the PCB (NOT THE TOP!) - solder the leads on the top of the board. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/wifi.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi.JPG}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/wifi6.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi6.JPG}}]] |
| + | [[https://s3.amazonaws.com/digispark/images/m/wifi7.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi7.JPG}}]] | ||
| Cut two lengths of male headers each 9 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin. | Cut two lengths of male headers each 9 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin. | ||
| Line 68: | Line 71: | ||
| **Note:** If you are using stackable headers, use them here instead of the standard male headers. | **Note:** If you are using stackable headers, use them here instead of the standard male headers. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/wifi.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi.JPG}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/wifi8.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi8.JPG}}]] |
| + | [[https://s3.amazonaws.com/digispark/images/m/wifi9.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi9.JPG}}]] | ||
| + | Plug antenna into WiFi module. Optionally affix antenna to board as shown - using tape, hot glue, or similar. | ||
| + | [[https://s3.amazonaws.com/digispark/images/m/wifi10.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi10.JPG}}]] | ||
| + | [[https://s3.amazonaws.com/digispark/images/m/wifi11.JPG|{{https://s3.amazonaws.com/digispark/images/t/wifi11.JPG}}]] | ||
| + | =====WiFi Module Setup:===== | ||
| + | |||
| + | [[digispark:tutorials:wififirstsetup|First Time Use Setup]] | ||
| + | |||
| + | [[digispark:tutorials:wificlient|WiFi Client Use Setup]] | ||
| + | |||
| + | [[digispark:tutorials:wifiserver|WiFi Server Use Setup]] | ||
| =====Programming:===== | =====Programming:===== | ||
| + | Several Examples can be found under Files->Examples->Digispark_Examples-> in the newest Digistump IDE releases 1.5.8A and higher | ||
| + | |||
| + | **NOTE: You must follow the setup guides above for the Client or Server setup, before using the examples.** | ||
digispark/tutorials/prowifi.txt · Last modified: 2016/06/09 12:03 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
