digispark:tutorials:proproto
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
digispark:tutorials:proproto [2014/11/24 14:54] digistump |
digispark:tutorials:proproto [2016/06/09 12:03] (current) |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| =====Product Description:===== | =====Product Description:===== | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/proproto1.jpg|{{https://s3.amazonaws.com/digispark/images/t/proproto1.jpg}}]][[https://s3.amazonaws.com/digispark/images/m/proproto2.jpg|{{https://s3.amazonaws.com/digispark/images/t/proproto2.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/proproto1.JPG|{{https://s3.amazonaws.com/digispark/images/t/proproto1.JPG}}]][[https://s3.amazonaws.com/digispark/images/m/proproto2.JPG|{{https://s3.amazonaws.com/digispark/images/t/proproto2.JPG}}]] |
| The Pro Prototype Shield Kit breaks out the connections on the Digispark Pro development board and provides a small through hole soldering area for building custom circuits. | The Pro Prototype Shield Kit breaks out the connections on the Digispark Pro development board and provides a small through hole soldering area for building custom circuits. | ||
| Line 28: | Line 28: | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/proproto1.jpg|{{https://s3.amazonaws.com/digispark/images/t/proproto1.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/proproto1.JPG|{{https://s3.amazonaws.com/digispark/images/t/proproto1.JPG}}]] |
| Cut two lengths of male headers each 9 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin. | Cut two lengths of male headers each 9 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/proproto3.jpg|{{https://s3.amazonaws.com/digispark/images/t/proproto3.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/proproto3.JPG|{{https://s3.amazonaws.com/digispark/images/t/proproto3.JPG}}]] |
| - | [[https://s3.amazonaws.com/digispark/images/m/proproto2.jpg|{{https://s3.amazonaws.com/digispark/images/t/proproto2.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/proproto2.JPG|{{https://s3.amazonaws.com/digispark/images/t/proproto2.JPG}}]] |
| **Tip:** Inseting the headers into a breadboard and then placing the board on top can make this process easier. | **Tip:** Inseting the headers into a breadboard and then placing the board on top can make this process easier. | ||
| **Note:** If you are using stackable headers, use them here instead of the standard male headers. | **Note:** If you are using stackable headers, use them here instead of the standard male headers. | ||
digispark/tutorials/proproto.1416869680.txt.gz · Last modified: 2014/11/24 14:54 by digistump
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
