digispark:tutorials:progtool
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | Next revision Both sides next revision | ||
|
digispark:tutorials:progtool [2013/04/24 11:40] digistump |
digispark:tutorials:progtool [2013/04/24 11:41] digistump |
||
|---|---|---|---|
| Line 44: | Line 44: | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/prog1.JPG|{{https://s3.amazonaws.com/digispark/images/t/prog1.JPG}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/prog1.jpg|{{https://s3.amazonaws.com/digispark/images/t/prog1.jpg}}]] |
| Insert the female and male USB connectors on either end of the board matching them up with the labels "male" and "female" on the board. You may need to bend the female connector legs (the two thick pins) out a bit to get it to fit. | Insert the female and male USB connectors on either end of the board matching them up with the labels "male" and "female" on the board. You may need to bend the female connector legs (the two thick pins) out a bit to get it to fit. | ||
| Line 50: | Line 50: | ||
| Flip over and solder all the pins and legs. | Flip over and solder all the pins and legs. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/prog2.JPG|{{https://s3.amazonaws.com/digispark/images/t/prog2.JPG}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/prog2.jpg|{{https://s3.amazonaws.com/digispark/images/t/prog2.jpg}}]] |
| - | [[https://s3.amazonaws.com/digispark/images/m/prog5.JPG|{{https://s3.amazonaws.com/digispark/images/t/prog5.JPG}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/prog5.jpg|{{https://s3.amazonaws.com/digispark/images/t/prog5.jpg}}]] |
| Insert the switch and flip over and solder - some tape or putty to hold the switch in place can be a big help. | Insert the switch and flip over and solder - some tape or putty to hold the switch in place can be a big help. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/prog6.JPG|{{https://s3.amazonaws.com/digispark/images/t/prog6.JPG}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/prog6.jpg|{{https://s3.amazonaws.com/digispark/images/t/prog6.jpg}}]] |
| Line 63: | Line 63: | ||
| **NOTE:** If you do not want a red indicator LED when the switch is off, leave off the resistor and LED | **NOTE:** If you do not want a red indicator LED when the switch is off, leave off the resistor and LED | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/prog7.JPG|{{https://s3.amazonaws.com/digispark/images/t/prog7.JPG}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/prog7.jpg|{{https://s3.amazonaws.com/digispark/images/t/prog7.jpg}}]] |
| Insert the red LED, flip over and solder, cut off the excess of the leads. | Insert the red LED, flip over and solder, cut off the excess of the leads. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/prog3.JPG|{{https://s3.amazonaws.com/digispark/images/t/prog3.JPG}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/prog3.jpg|{{https://s3.amazonaws.com/digispark/images/t/prog3.jpg}}]] |
| Plug into a USB port or cable, insert a Digispark (or other device), and flip the switch - when the LED is lit the device is off, when it is not lit the device is on! | Plug into a USB port or cable, insert a Digispark (or other device), and flip the switch - when the LED is lit the device is off, when it is not lit the device is on! | ||
digispark/tutorials/progtool.txt · Last modified: 2016/06/09 12:03 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
