digispark:tutorials:oled
Differences
This shows you the differences between two versions of the page.
|
digispark:tutorials:oled [2014/11/08 18:32] digistump created |
digispark:tutorials:oled [2016/06/09 12:03] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ======Pro OLED Shield Kit Tutorial====== | ||
| - | =====Product Description:===== | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/oled.jpg|{{https://s3.amazonaws.com/digispark/images/t/oled.jpg}}]] | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/oled.jpg|{{https://s3.amazonaws.com/digispark/images/t/oled.jpg}}]] | ||
| - | |||
| - | This is an unassembled kit and requires basic soldering. This is designed for use with the Digispark development board, which is not included. | ||
| - | |||
| - | =====Parts:===== | ||
| - | |||
| - | ^ Part ^ Quantity ^Identification^ | ||
| - | | Pro Combo PCB|1| | | ||
| - | | 4.7K (4K7) Ohm 1/4W resistor 1% or 5%|2| Yellow - Violet - Red| | ||
| - | | I2C OLED Module |1|| | ||
| - | | 1x40pin male 0.1" pitch header| 21 pins worth| | | ||
| - | |||
| - | |||
| - | **Resistor Values:** For more information on how to identify the value of the resistors we recommend these sites: | ||
| - | A nice simple resistor calculator: http://www.ealnet.com/m-eal/resistor/resistor.htm | ||
| - | A comprehensive article on identification: http://www.diyaudioandvideo.com/Electronics/Color/ | ||
| - | |||
| - | **Soldering:** If you are new to soldering we recommend the following tutorials: | ||
| - | Soldering Basics (http://www.sparkfun.com/tutorials/106) and Soldering Crash Course from the folks at Sparkfun (http://www.sparkfun.com/tutorials/354). | ||
| - | How to solder from the Curious Inventor: http://store.curiousinventor.com/guides/How_to_Solder | ||
| - | |||
| - | Adafruit has this excellent guide that starts with the tools needed and then shows detailed pictures, including some of the common problems that beginners experience (http://learn.adafruit.com/adafruit-guide-excellent-soldering) | ||
| - | |||
| - | **We assume for these assembly instructions that you know the basics of thru-hole soldering. If you don't check out the links above, these boards are very easy to solder - we promise!** | ||
| - | |||
| - | |||
| - | =====Assembly:===== | ||
| - | |||
| - | |||
| - | [[https://s3.amazonaws.com/digispark/images/m/oled.jpg|{{https://s3.amazonaws.com/digispark/images/t/oled.jpg}}]] | ||
| - | |||
| - | Solder resistors one at a time. Solder the leads and clip off the excess. Repeat for both resistors. | ||
| - | |||
| - | [[https://s3.amazonaws.com/digispark/images/m/oled.jpg|{{https://s3.amazonaws.com/digispark/images/t/oled.jpg}}]] | ||
| - | |||
| - | |||
| - | Cut two lengths of male headers each 9 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin. | ||
| - | |||
| - | **Tip:** Inserting the headers into a breadboard and then placing the board on top can make this process easier. | ||
| - | |||
| - | **Note:** If you are using stackable headers, use them here instead of the standard male headers. | ||
| - | |||
| - | [[https://s3.amazonaws.com/digispark/images/m/oled.jpg|{{https://s3.amazonaws.com/digispark/images/t/oled.jpg}}]] | ||
| - | |||
| - | Insert the OLED module into the front of the board matching the pins labeled for the OLED module. Solder the pins on the back, optionally snip off the excess. | ||
| - | |||
| - | [[https://s3.amazonaws.com/digispark/images/m/oled.jpg|{{https://s3.amazonaws.com/digispark/images/t/oled.jpg}}]] | ||
| - | |||
| - | |||
| - | |||
| - | =====Programming:===== | ||
| - | |||
| - | |||
| - | |||
| - | Grab the library at: https://github.com/Defragster/OLEDPRO | ||
| - | Move the MicroLCDpro folder into your arduino libraries folder | ||
digispark/tutorials/oled.txt · Last modified: 2016/06/09 12:03 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
