User Tools

Site Tools


digispark:tutorials:littlewire

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
digispark:tutorials:littlewire [2013/11/13 22:34]
digistump [Assembly:]
digispark:tutorials:littlewire [2016/06/09 12:03] (current)
Line 3: Line 3:
 =====Product Description:​===== =====Product Description:​=====
 [[https://​s3.amazonaws.com/​digispark/​images/​m/​lw1.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​lw1.jpg}}]] [[https://​s3.amazonaws.com/​digispark/​images/​m/​lw1.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​lw1.jpg}}]]
-[[https://​s3.amazonaws.com/​digispark/​images/​m/​lw2.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​lw2.jpg}}]][[https://​s3.amazonaws.com/​digispark/​images/​m/​lw3.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​lw3.jpg}}]]+[[https://​s3.amazonaws.com/​digispark/​images/​m/​lw6.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​lw6.jpg}}]][[https://​s3.amazonaws.com/​digispark/​images/​m/​lw7.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​lw7.jpg}}]]
  
-The Little Wire on Digispark Shield Kit connects ​provides a Little Wire compatible pinout on the Digispark. This allows the Digispark to be easily used as a Little Wire device, with the Little Wire firmware and libraries. The shield also provide pull-ups for the I2C lines, which can be enabled by an included jumper, and an external power jumper. The kit also includes a 6 pin IDC cable for connecting to other circuits or to standard 6-pin AVR ISP headers for programming AVR chips.+The Little Wire on Digispark Shield Kit provides a Little Wire compatible pinout on the Digispark. This allows the Digispark to be easily used as a Little Wire device, with the Little Wire firmware and libraries. The shield also provide pull-ups for the I2C lines, which can be enabled by an included jumper, and an external power jumper. The kit also includes a 6 pin IDC cable for connecting to other circuits or to standard 6-pin AVR ISP headers for programming AVR chips.
  
-Little Wire is multi-featured USB controlled Open Source Hardware tool packed in a minimal form factor designed by Ihsan Kehribar. Little Wire appears as usbtinyisp device and provides a tethered interface between hardware and a computer.+Little Wire is multi-featured USB controlled Open Source Hardware tool packed in a minimal form factor designed by Ihsan Kehribar. ​The Little Wire for Digispark shield was designed by Ihsan in collaboration with Digistump. The Little Wire firmware can be easily loaded on to Digispark for use with the Little Wire for Digispark shield.
  
 Little Wire has the following features: Little Wire has the following features:
Line 26: Line 26:
 | Little Wire Shield PCB|1| | | Little Wire Shield PCB|1| |
 | 6-pin IDC Cable|1| | | 6-pin IDC Cable|1| |
-| 4.7k ohm 1/4W 5% resistor|2| ​Brown Black Yellow|+| 4.7k ohm 1/4W 5% resistor|2| ​Yellow ​Violet ​Red|
 | 0.1" pitch Jumper/​Shunt |2| | | 0.1" pitch Jumper/​Shunt |2| |
 | 1x40pin male 0.1" pitch header| 22 pins worth| | | 1x40pin male 0.1" pitch header| 22 pins worth| |
Line 64: Line 64:
  
 [[https://​s3.amazonaws.com/​digispark/​images/​m/​lw5.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​lw5.jpg}}]] [[https://​s3.amazonaws.com/​digispark/​images/​m/​lw5.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​lw5.jpg}}]]
- 
-If using the cable - plug into 6 pin header. 
- 
-[[https://​s3.amazonaws.com/​digispark/​images/​m/​lw6.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​lw6.jpg}}]] 
  
 Cut a length of male headers 6 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin. Cut a length of male headers 6 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin.
- 
-[[https://​s3.amazonaws.com/​digispark/​images/​m/​lw7.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​lw7.jpg}}]] 
  
 **Tip:** Inseting the headers into a breadboard and then placing the board on top can make this process easier. **Tip:** Inseting the headers into a breadboard and then placing the board on top can make this process easier.
Line 77: Line 71:
 **Note:** If you are using stackable headers, use them here instead of the standard male headers. **Note:** If you are using stackable headers, use them here instead of the standard male headers.
  
-=====Using external 1-wire deivces:=====+[[https://​s3.amazonaws.com/​digispark/​images/​m/​lw6.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​lw6.jpg}}]] 
 + 
 + 
 +If using the cable plug into 6 pin header. 
 + 
 +[[https://​s3.amazonaws.com/​digispark/​images/​m/​lw7.jpg|{{https://​s3.amazonaws.com/​digispark/​images/​t/​lw7.jpg}}]] 
  
-External 1-wire devices can be added to the same 1-wire bus by connecting them to the 3 pin screw terminal - following the labeled pin outs on the board. ​ 
  
-Sensors other than the DS18B20 will not be covered in the included examples, but many examples are readily available online. ​+=====Loading ​the firmware:​=====
  
 +Download the Little Wire firmware installer for your platform here - Under "​Single click installers for v1.3 firmware"​ - http://​littlewire.cc/​downloads.html
  
-=====Programming:​=====+Run the executable and when prompted plug in the Digispark that you will be using with the shield. When complete the Digispark will now appear as a Little Wire device 5 seconds after it is plugged into the computer. ​
  
-With the newest version of the Digispark Arduino IDE goto Examples->​OneWire->​Digispark Example 
  
-This example uses P5 by default - to use P1 change this lineOneWire ds(5); to OneWire ds(1);+=====Use:=====
  
 +See http://​littlewire.cc for documentation,​ libraries, and more!
  
digispark/tutorials/littlewire.1384410872.txt.gz · Last modified: 2013/11/13 22:34 by digistump