digispark:tutorials:digispark
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
digispark:tutorials:digispark [2012/12/19 00:27] digistump created |
digispark:tutorials:digispark [2016/06/09 12:03] (current) |
||
|---|---|---|---|
| Line 7: | Line 7: | ||
| [[https://s3.amazonaws.com/digispark/images/m/digispark3.jpg|{{https://s3.amazonaws.com/digispark/images/t/digispark3.jpg}}]] | [[https://s3.amazonaws.com/digispark/images/m/digispark3.jpg|{{https://s3.amazonaws.com/digispark/images/t/digispark3.jpg}}]] | ||
| - | ====Digispark: The micro-sized, affordable, Arduino enabled, usb development board!==== | + | ====Digispark: The micro-sized, affordable, Arduino enabled, USB development board!==== |
| - | The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark is a great way to jump into electronics, or perfect for when an Arduino is too big or too much. | + | The Digispark is an ATtiny85 based microcontroller development board similar to the Arduino line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark is a great way to jump into electronics, or perfect for when an Arduino is too big or too much. |
| The Digispark is shipped fully assembled except for the two included and easy to solder headers. | The Digispark is shipped fully assembled except for the two included and easy to solder headers. | ||
| - | Here are the specs: | + | Here are the specifications: |
| - | * Support for the Arduino IDE 1.0+ (OSX/Win/Linux) | + | * Support for the Arduino IDE 1.0 and later (OS X, Windows, and Linux) |
| - | * Power via USB or External Source - 5v or 7-35v (automatic selection) | + | * Power via USB or external source - 5 V or 7-35 V (automatic selection) |
| - | * On-board 500ma 5V Regulator | + | * On-board 500 mA 5 V Regulator |
| * Built-in USB | * Built-in USB | ||
| - | * 6 I/O Pins (2 are used for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB) | + | * 6 I/O pins (2 are used for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB) |
| - | * 8k Flash Memory (about 6k after bootloader) | + | * 8 KB flash memory (about 6 KB after bootloader) |
| - | * I2C and SPI (vis USI) | + | * I²C and SPI (vis USI) |
| - | * PWM on 3 pins (more possible with Software PWM) | + | * PWM on 3 pins (more possible with software PWM) |
| * ADC on 4 pins | * ADC on 4 pins | ||
| - | * Power LED and Test/Status LED | + | * Power LED and test/status LED |
| + | |||
| + | Schematic is https://s3.amazonaws.com/digispark/DigisparkSchematicFinal.pdf | ||
digispark/tutorials/digispark.1355905638.txt.gz · Last modified: 2012/12/19 00:27 by digistump
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
