digispark:tutorials:button
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
digispark:tutorials:button [2014/11/08 13:55] digistump created |
digispark:tutorials:button [2016/06/09 12:03] (current) |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| =====Product Description:===== | =====Product Description:===== | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/button.jpg|{{https://s3.amazonaws.com/digispark/images/t/button.jpg}}]][[https://s3.amazonaws.com/digispark/images/m/button.jpg|{{https://s3.amazonaws.com/digispark/images/t/button.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/button1.JPG|{{https://s3.amazonaws.com/digispark/images/t/button1.JPG}}]][[https://s3.amazonaws.com/digispark/images/m/button4.JPG|{{https://s3.amazonaws.com/digispark/images/t/button4.JPG}}]] |
| Line 34: | Line 34: | ||
| Empty kit bag (or if using a raw PCB, acquire parts) and verify contents. | Empty kit bag (or if using a raw PCB, acquire parts) and verify contents. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/button.jpg|{{https://s3.amazonaws.com/digispark/images/t/button.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/button1.JPG|{{https://s3.amazonaws.com/digispark/images/t/button1.JPG}}]] |
| Insert the resistor through the top and solder on bottom of board. Cut excess leads. | Insert the resistor through the top and solder on bottom of board. Cut excess leads. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/button.jpg|{{https://s3.amazonaws.com/digispark/images/t/button.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/button2.JPG|{{https://s3.amazonaws.com/digispark/images/t/button2.JPG}}]] |
| Insert button on top and solder four leads on the bottom. | Insert button on top and solder four leads on the bottom. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/button.jpg|{{https://s3.amazonaws.com/digispark/images/t/button.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/button3.JPG|{{https://s3.amazonaws.com/digispark/images/t/button3.JPG}}]] |
| Cut a length of male headers 6 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin. | Cut a length of male headers 6 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin. | ||
| Line 51: | Line 51: | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/button.jpg|{{https://s3.amazonaws.com/digispark/images/t/button.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/button4.JPG|{{https://s3.amazonaws.com/digispark/images/t/button4.JPG}}]] |
| + | |||
| + | [[https://s3.amazonaws.com/digispark/images/m/button5.JPG|{{https://s3.amazonaws.com/digispark/images/t/button5.JPG}}]] | ||
| Your Button shield is complete! | Your Button shield is complete! | ||
digispark/tutorials/button.1415483713.txt.gz · Last modified: 2014/11/08 13:55 by digistump
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
