digispark:tutorials:breakout
Differences
This shows you the differences between two versions of the page.
|
digispark:tutorials:breakout [2012/12/18 23:30] digistump created |
digispark:tutorials:breakout [2016/06/09 12:03] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ======Breakout Shield Kit (Version A and B) Tutorial====== | ||
| - | =====Product Description:===== | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/breakout1.jpg|{{https://s3.amazonaws.com/digispark/images/t/breakout1.jpg}}]][[https://s3.amazonaws.com/digispark/images/m/breakout4.jpg|{{https://s3.amazonaws.com/digispark/images/t/breakout4.jpg}}]][[https://s3.amazonaws.com/digispark/images/m/breakout2.jpg|{{https://s3.amazonaws.com/digispark/images/t/breakout2.jpg}}]] | ||
| - | |||
| - | The Breakout Shield Kit breaks out each i/o connection on the Digispark development board and provides them as three pin headers with a 5V, Gnd, and i/o pin for each. This allows the easy connection of third-party and homemade sensors, servos, and more. The Version A kit provides headers in the order of GND / 5V / I/O Pin | ||
| - | Version B kit provides headers in the order of GND / I/O Pin / 5V | ||
| - | |||
| - | This is an unassembled kit and requires basic soldering. Use of it requires surface mount soldering. This is designed for use with the Digispark development board, which is not included. | ||
| - | |||
| - | |||
| - | =====Parts:===== | ||
| - | |||
| - | ^ Part ^ Quantity ^Identification^ | ||
| - | | Breakout Shield PCB|1| | | ||
| - | | 1x40pin male 0.1" pitch header| 27 pins worth| | | ||
| - | |||
| - | **Soldering:** If you are new to soldering we recommend the following tutorials: | ||
| - | Soldering Basics (http://www.sparkfun.com/tutorials/106) and Soldering Crash Course from the folks at Sparkfun (http://www.sparkfun.com/tutorials/354). | ||
| - | How to solder from the Curious Inventor: http://store.curiousinventor.com/guides/How_to_Solder | ||
| - | |||
| - | **We assume for these assembly instructions that you know the basics of thru-hole soldering. If you don't check out the links above, these boards are very easy to solder - we promise!** | ||
| - | |||
| - | |||
| - | =====Assembly:===== | ||
| - | |||
| - | [[https://s3.amazonaws.com/digispark/images/m/breakout1.jpg|{{https://s3.amazonaws.com/digispark/images/t/breakout1.jpg}}]] | ||
| - | |||
| - | Cut six lengths of male headers 3 pins long. Insert one each on the top of the board, into each set of 3 pin connections and solder each pin. | ||
| - | |||
| - | [[https://s3.amazonaws.com/digispark/images/m/breakout3.jpg|{{https://s3.amazonaws.com/digispark/images/t/breakout3.jpg}}]] | ||
| - | |||
| - | Cut a length of male headers 6 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin. | ||
| - | |||
| - | [[https://s3.amazonaws.com/digispark/images/m/breakout2.jpg|{{https://s3.amazonaws.com/digispark/images/t/breakout2.jpg}}]] | ||
| - | |||
| - | **Tip:** Inseting the headers into a breadboard and then placing the board on top can make this process easier. | ||
| - | |||
| - | **Note:** If you are using stackable headers, use them here instead of the standard male headers. | ||
| - | |||
| - | =====Programming:===== | ||
| - | |||
| - | Please refer to the sample code provided by the sensor or other module you will be attaching. | ||
digispark/tutorials/breakout.txt · Last modified: 2016/06/09 12:03 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
