digispark:tutorials:ble
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
digispark:tutorials:ble [2014/11/16 16:37] bigluc Notated a known bug in example code |
digispark:tutorials:ble [2015/02/11 09:54] digistump |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| =====Product Description:===== | =====Product Description:===== | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/ble.jpg|{{https://s3.amazonaws.com/digispark/images/t/ble.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/ble1.jpg|{{https://s3.amazonaws.com/digispark/images/t/ble1.jpg}}]] |
| - | [[https://s3.amazonaws.com/digispark/images/m/ble.jpg|{{https://s3.amazonaws.com/digispark/images/t/ble.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/ble4.jpg|{{https://s3.amazonaws.com/digispark/images/t/ble4.jpg}}]] |
| Line 32: | Line 32: | ||
| =====Assembly:===== | =====Assembly:===== | ||
| - | Empty kit bag (or if using a raw PCB, aquire parts) and verify contents. | + | Empty kit bag (or if using a raw PCB, acquire parts) and verify contents. |
| - | [[https://s3.amazonaws.com/digispark/images/m/ble.jpg|{{https://s3.amazonaws.com/digispark/images/t/ble.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/ble1.jpg|{{https://s3.amazonaws.com/digispark/images/t/ble1.jpg}}]] |
| Insert 6 pin right angle socket into top of PCB - insert it into the set of 6 holes that say "BLE BT4" below them - this is the second set from the right edge of the board. Solder socket pins on the bottom of the board | Insert 6 pin right angle socket into top of PCB - insert it into the set of 6 holes that say "BLE BT4" below them - this is the second set from the right edge of the board. Solder socket pins on the bottom of the board | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/ble.jpg|{{https://s3.amazonaws.com/digispark/images/t/ble.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/ble2.jpg|{{https://s3.amazonaws.com/digispark/images/t/ble2.jpg}}]] |
| Cut two lengths of male headers each 9 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin on the top. | Cut two lengths of male headers each 9 pins long and one 3 pins long. Insert into corresponding positions (on the bottom of the board) and solder each pin on the top. | ||
| Line 46: | Line 46: | ||
| **Note:** If you are using stackable headers, use them here instead of the standard male headers. | **Note:** If you are using stackable headers, use them here instead of the standard male headers. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/ble.jpg|{{https://s3.amazonaws.com/digispark/images/t/ble.jpg}}]] | + | [[https://s3.amazonaws.com/digispark/images/m/ble3.jpg|{{https://s3.amazonaws.com/digispark/images/t/ble3.jpg}}]] |
| Insert the HM-10 BLE breakout module into the 6 pin socket as shown. | Insert the HM-10 BLE breakout module into the 6 pin socket as shown. | ||
| - | [[https://s3.amazonaws.com/digispark/images/m/ble.jpg|{{https://s3.amazonaws.com/digispark/images/t/ble.jpg}}]] | ||
| - | + | [[https://s3.amazonaws.com/digispark/images/m/ble4.jpg|{{https://s3.amazonaws.com/digispark/images/t/ble4.jpg}}]] | |
| - | [[https://s3.amazonaws.com/digispark/images/m/ble.jpg|{{https://s3.amazonaws.com/digispark/images/t/ble.jpg}}]] | + | |
| =====Programming:===== | =====Programming:===== | ||
| + | For advanced AT commands (for changing name, etc) see the datasheet for the HM-10 module that is used on this shield: {{:digispark:tutorials:bluetooth40_en.pdf|}} | ||
| + | |||
| + | For ANCS (Apple Notification Center Service) instructions see here (Note: Please use the forums for all ANCS support - we cannot support it directly as we do not have experience with it): [[digispark:tutorials:hm10ancs|digispark:tutorials:hm10ancs]] | ||
| + | |||
| + | **Mobile app examples for Android and iOS (iOS development requires iOS dev setup or jailbroken phone)(phonegap/cordova based):** | ||
| + | (these can be edited with only a working knowledge of Javascript and HTML - see phonegap.com for more about how it all works) | ||
| + | |||
| + | https://github.com/digistump/Digispark_Cordova_BLEShieldEcho | ||
| + | |||
| + | https://github.com/digistump/Digispark_Cordova_BLEShieldRobot | ||
| + | |||
| + | Mobile Robot App for iOS - in ObjC - by Miirek: https://github.com/Miirek/BLEBot | ||
| **Example changing DigiLED over BLE** | **Example changing DigiLED over BLE** | ||
| - | **//Example has a bug. parseInt(); not included in Digispark loader.//** | + | <del>**//Example has a bug. parseInt(); not included in Digispark loader.//**</del>- Fixed in Digistump IDE Release 1.0+ |
| <code> | <code> | ||
| Line 101: | Line 111: | ||
| // look for the newline. That's the end of your | // look for the newline. That's the end of your | ||
| // sentence: | // sentence: | ||
| - | // if (mySerial.read() == '\n') { | ||
| if (Serial.read() == '\n') { | if (Serial.read() == '\n') { | ||
| // sends confirmation | // sends confirmation | ||
digispark/tutorials/ble.txt · Last modified: 2016/06/09 12:03 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
